We have been producing telecommunication devices in Turkey since 1981.We specialize in manufacturing of:
- Telephone call counters: to set price to phone calls instantly. These devices are used by private people, companies such as shops, restaurants, hotels, kiosks and also by the state post offices.

- Telephone FCT switch: this device provides the cheapest rate for a particular call, since it automatically directs fixed phones calls to fixed local telecom company lines and GSM calls to the corresponding GSM service company.

This device provides the cheapest rate for a particular call, since it automatically directs PTT calls to PTT lines and GSM calls to the corresponding GSM service company.

FCT switch:
FCT allows you to make your GSM calls using a regular phone.
FCT switch has the following feature: It determines the call type and directs the call to the corresponding phone service provider. That is, if you call a PTT number, FCT switch makes the call thorugh the regular phone lines. If you call a GSM number, FCT directs your call thorugh the GSM company lines. Thus, your calls become cheaper, (because calls made between the subscribers of the same operator have cheaper rates).

OPERATION
Place the SIM card to the SIM slot and connect the PTT line to the PTT input. Turn the power on and connect the phone output to the phone. Now, the switch is
ready to use. You can make calls using the phone. The FCT switch checks the numbers you dialed to determine the call type. If your call is a GSM call, it is directed to the GSM line. If the call is PTT call, then it is directed to the PTT line.

PROGRAMMING
You can program your device using the keypad on the phone.

Hold the receiver, then press *.
You can enter network, counter unit time for 12 KHz signal by pressing
1 , n ,  1x , 2x , 3x, 4t , 5t

You can enter unit counter time for international calls by pressing
1  5 0 0 *  0  3 (means: unit counter time is 3 seconds for international calls.)

You can determine the number of digits for a call by pressing
2 , x , x

You can set the start signal properties by pressing
* , 3 , 1 ,  #                                        On ; start signal enabled
* , 3 ,  1 ,  *                                        Off ; start signal disabled
* , 3 , 2 ,  #                                         On ; FCT switch enabled
* , 3 , 2 ,  *                                         Off ; FCT switch disabled
* , 3 , 3 ,  #                                         On ; ringer on 
* , 3 , 3 ,  *                                          Off ; ringer off

You can set the outgoing voice properties by pressing
4 , ( 0.7 )                    0= lowest volume level. 7= highest volume level.  Default= 4

You can set the incoming voice properties by pressing
5 , ( 0.4 )                    0= lowest volume level. 4= highest volume level.  Default= 2

You can select the FCT switch by pressing
* ,  7 ,  *                                GSM calls only. ( No need to have a PTT line )
* ,  7 ,  #                                GSM or PTT calls are allowed. PTT line should be connected to the device.

You can load the default values by pressing
* , 0

OPERATION with a CALL COUNTER
It generates 12 KHz signal to make the call counter work properly. The duration of counter signal is programmable.
You can also assign different unit counter time for different service providers. Also it can be programmed to call for particular GSM service providers.


TECHNICAL SPECIFICATIONS
Dual Band :(900-1800 MHz)
Power supply :220 V, 50 Hz.
Weight (FCT part) :400 gr.
Weight (power supply) :850 gr.
Dimensions :5.3x12.7x14.5 cm

It automatically sets price to phone calls. Thus, it provides telephone calls for customers in shops, restaurants, hotels, kiosks. In this way, the owners of these devices are able to provide a useful service to their customers and make profit at the same time.

Our telephone call counters estimate the price of the call instantly
Different models with and without 12 KHz signal are available counter with 12 KHz signal operates based on the telecom company counter signal. Counter without 12 KHz operates based on its own program. The user can see the price through an additional monitor.

Model : counter device without 12 khz signal
It operates without 12 KHz rate signal from the post office. It computes the total cost of a phone call depending on the total call duration and the call location.

Model 2: telephone call counter
It operates using the 12 KHz counter signal of the post office.It computes the total cost of a phone call in terms of local currency and the number of counters. An additional display can be connected to allow the user monitor the total. 

Model 3: addıtıonal dısplay
Allows the user observe the total amount he should pay during the call. The user can only see the total amount. He is not allowed to do any other operation, such as, resetting the device.

ABOUT THE CALL COUNTER

The call counter performs estimation based on the information provided via  12/16 Khz. signal and reversal polarity  from the exchange system. The cost of a call is estimated by the signals received from the PTT.  In addition, the user can set the price for the number of units extracted from the call counter.  This system can provide the amount of counters by periods or terms.

 * ENTERING UNIT PRICE

The unit price of counter  is saved in the call counter's memory by using the buttons located at the top of the machine.  After the telephone reciever is lifted the Reset and counter button should be pushed for 3 seconds.  The two buttons are released as the letter "F" appears on the monitor.  It counts backwards as the counter or forward reset button is pushed.  It automatically goes forward ıf these buttons are pushed continously.  The transation will be recorded as the telephone receiver is closed.

 * SEEING THE NUMBER OF COUNTER

 In order to see the transaction in terms of counter units the counter button should be pushed.  The letter (C) and 3 counter ınsertions appears at the top right corner of the monitor.  These will be eraesed by pushing the reset button.

* MONITORING THE  PERIODICAL TOTAL AMMOUNT

 The periodical total amount is automatically saved by the system for accounting purposes.  In order to see the total amont press the reset button for 3 seconds.  As a result a fıve-digit periodical amount ıs displayed at the rıght corner of the monitor.  The total amount can not be eraesed.

 * SEEING THE PRICE WITHOUT LIFTING THE TELEPHONE RECEIVER

The telephone machine could be away from the call counter.  In order to display the cost of a call without lifting the telephone receiver, the �screen� button should be pressed.

* ADDITIONAL DIVICE

The customer is allowed to see the amount with a additional monitor.  There are no additional buttons on this monitor.  In addition, the customer can not reset the additional device.  The additional device operates as soon as the telephone receiver is lifted.  The additional divice is connected by a 6-wire cable. The max. distance from call counter to additional display is 15 mt.  The additional device recieves its power directly from the PTT.

TECHNİCAL SPECIFICATIONS :

Input signal               : 12 Khz , 16 K hz. or reversal polarity.

Display                     :  6 haneli LED display.

Dönemsel toplam    :  6 haneli

Power                      : Only PTT line , no need any power.

 Weight                     : 300 gr

Dimensions              : 4.5 x 13.5 x 17 cm

 * INSTALLATION (There are two different installations)

1-Installation without the monitor: the PTT line should be connected to the device's input section containing white and brown tips.   The line exiting the device is connected to the telephone's input section.

2- Installation with the monitor: the PTT line should be connected to the device's input section containing white and brown tips.  The 6 cable data lines connected to the call counter's DATA socket and monitor's data socket.  The telephone is connected to the monitor's telephone output.